Control Panel

  • Using integrated control systems demonstrate excellent performance
  • Adopting branded contactors and relays ensure reliability
  • Reasonable wire layout, avoid interference
  • No need to install weighting device, start smoothly.
  • Direct landing, high driving efficiency
  • EMC and CE Service floor can be chosen
  • Adjustable design for the cabinet, can be installed on wall
machine-room-less-lift-controller-500x500

MRL LIFT CONTROL PANEL

  • Compafible to EN81-1+A3 standards
  • Operates with synchronous and inducfion motors
  • ARL 300 controller card
  • Arkel A-Drive & Fuji Frenic-Lih & Ziehl – Abegg Zetadyn inventer opfions
  • Speed: up to 1,6 m/sn, Number of stops: Up to 24
  • 4 Lihs group operafion
  • Emergency rescue with UPS ( easy direcfion )
  • Door pre – opening and relevelling
  • Compafible with all kinds of auto doors and manuel doors
  • 2 door controls for cabins with double entrances
  • 7 segment & grey cod & binary cod display opfions
  • Panel illuminafion and cooling fan
  • Easy installafion with serial communicafion with cabin
machine-room-less-lift-controller-500x500

HYDRAULIC LIFT CONTROL PANEL

  • Compafible to EN81-1+A3 standards
  • ARL 300 controller card
  • Direct drive & Star Delta drive & Driving with soh starter
  • Speed: up to 1,2 m/sn, Number of stops: Up to 24
  • Emergency rescue with UPS
  • Door pre – opening and relevelling
  • Compafible with all kinds of auto doors and manuel doors
  • 2 door controls for cabins with double entrances
  • 7 segment & grey cod & binary cod display opfions
  • Panel illuminafion and cooling fan
  • Easy installafion with serial communicafion with cabin
hydraulic-lift-control-panel-system-500x500

MR LIFT CONTROL PANEL

  • Compafible to EN81-1+A3 standards
  • Operates with synchronous and inducfion motors
  • ARL 300 controller card
  • Arkel A-Drive & Fuji Frenic-Lih & Ziehl – Abegg Zetadyn inventer opfions
  • Speed: up to 1,6 m/sn, Number of stops: Up to 24
  • 4 Lihs group operafion
  • Emergency rescue with UPS ( easy direcfion )
  • Door pre – opening and relevelling
  • Compafible with all kinds of auto doors and manuel doors
  • 2 door controls for cabins with double entrances
  • 7 segment & grey cod & binary cod display opfions
  • Panel illuminafion and cooling fan
  • Easy installafion with serial communicafion with cabin
mr m

MRL Machine

  •  High efficiency. By using this motor, it could save
  • 30% – 50% energy compared with the geared tracfion machine.
  • Small, simple and space saving.
  • Used the fully closed bearing, which is pollufion-free and maintenance free.
  • Low noise, small oscillafion, high comfort level in elevator run and good stable
  • The magnefic steel, which is made from heat reisifing rare earth, is stable and reliable.
  • Equip motor with thermal protector in order to make the motor never demagnefizing.
mr

BT Machine

  • Extremely robust and smooth
  • Very versafile machines with 100+ load and speed
  • Extremely long life machines with gear-pair center height adjustment for wear compansasfion
  • Dynamically balanced high-speed parts for smooth
  • Factory load tested and check for extreme
  • All parts manufactured to precision and interchangeability.
bt

Specially Design Safety Frame

Design

Panelling in numerous surface designs, glass door panels, aluminium and stainless-steel door sills and surrounding invisible sill guides enable individual adaptation to the design requirements in the building

Safety

Compliance with currently valid EU standards EN 81-20/-50 and national safety regulations High-quality door safety lock systems and short door reversal films for the safety of passengers and to protect the technology against damage

Efficiency

Time-saving installation resulting from clever, installation-friendly mounting solutions for short downfimes Short door opening and closing times reduce waiting periods and increase the handling capacity of the installation

Comfort

Low noise of ≤ 55 dB(A), measured one metre in front of the landing door Excellent smooth running properties and isolation from structure-borne sound as a result of mounts protected from vibration on the elevator car (SA 79) Harmonious and smooth door movements as a result of frequency-controlled door drive with adjustable running characteristic curves

Scope of Supply

Doors complete with required fastening material, basic body of the door sill, guide rail profile of the door sill and toe guards Rasterizing of the door height and door widths in increments of 50 mm possible (SA 20); with door type M4TZ with DW ≥ 1400 mm in increments of 100 mm

Flexibility

Very wide and finely graded range of options for door dimensions, with door widths from 700 to 2500 mm and door heights from 2000 to 2500 mm One-side opening, double-panel telescopic door (M2T) for optimum door width in a narrow shah Centre-opening, double-panel door (M2Z) for short door running times and high handling capacity Centre-opening, four-panel telescopic door (M4TZ) for maximum door widths with good ufilisafion of space Comprehensive range of options and special versions for individual adaptation

Door panels

The door panels are single-leaf, manufactured using noise-inhibiting sandwich design and offer outstanding corrosion protection. The basic body consists of 2 mm galvanised steel plate and is either laminated with 0.6 mm galvanised steel plate or with 0.8 mm stainless steel plate. Powder coating of the galvanised version is also possible. The lower door panel guide in the door sill for each door panel consists of two adjust- able sliders. Rubber buffers are fi5ed to the closing edge to buffer impacts and reduce noise. In the case of landing doors that lead out-doors, we recommend the use of door panels clad with stainless steel. In the case of fire resistant doors with heat insulation criterion, the door panels are filled with an additional technical heat insulation.

Door frame

The door frame comprises:the upper suspension gear made of folded 2.5 mm galvanised steel plate; the side door posts made of folded 1.5 mm galvanised steel plate; and the lower door sill made of folded 2 mm galvanised steel plate with bolted- on aluminium or stainless steel profile

Flooring

The customer-fi5ed flooring can be laid directly up to the outer door panel facing the hallway. Even more elegance is created with the door sill with surrounding guide of the door panels (SA 18): the flooring can be laid up to the shah edge. The same possibility applies to the car door (SA 18).

Door

Nikon Maintenance Management System(NMMS)

Nikon Maintenance Management System (NMMS) is a
predictive and preventive system, ensuring fewer service call
and less downtime than any other plan in the industry. We will
focus on your elevator. So you can focus on your building.
 
With Nikon MRL System, We re-examined every aspect of the elevator from design and
installation to operation and maintenance. The result is a system that moves to a new level.
shutterstock_119118088

NIKON ELEVATORS PVT. LTD.

Nikon Elevators Pvt. Ltd. Deals In Different Types Of Elevators Like Basic Lift, Hydraulic Lift. MRL Lift, Goods Elevators And Many More From Last 25 Years. 

Main Menu

  • Home
  • About
  • Products
  • Services
  • Gallery
  • Contact

Head Office :

  • Gr. floor “Mansi Complex” Nr. Vidyanagar High School, Sardar Patel Underbridge, Usmanpura, Ahmedabad-380 014.
  • nikonelevators@yahoo.co.in | sales@nikonelevators.com | www.nikonelevators.com
  • 079-27540355, 27540640